NEWS

Analysis of common process problems of disposable tissue closure clips (ligation clips)

2022-02-17


Materials for tissue closure clips (ligation clips)

1. POM material: This material has good mechanical strength and rigidity, good organic solvent resistance, strong repeated impact resistance, good wear resistance, and self-lubricating properties, but it is easy to decompose under high temperature for a long time during processing. Poor acid resistance and large molding shrinkage.

2. Polylactic acid material: It is a new type of biodegradable material with good biocompatibility, gloss, good heat resistance, good thermal stability of the material, and good solvent resistance, mechanical properties and The physical properties are good, and it is still in the early development stage in China. The material properties and characteristics require continuous experiments and verification. For details, please refer to the next issue.

Tissue closure clip mold features

The product itself has high requirements on the precision of the mold, and the corresponding material is easy to decompose, and has requirements on the entry point of the mold and the design of the runner. There are two main ways to open the mold:

1. Cold runner submerged glue: 1*2 and 1*4 are used for the ranking method

2. Needle valve type hot runner feeding: Due to the light weight of the tissue closure clip product, it belongs to micro-injection, and the material is easy to decompose. Using this method requires the physical properties of the material, the design of the hot runner system, and the design of the mold. , The selection of the molding machine and the design of the molding process are systematically and rigorously analyzed, and the requirements are relatively high. However, this method can greatly reduce the amount of material used, while significantly improving production efficiency.

Analysis and solutions of common problems of tissue closure clips

1. The product size is out of tolerance:

Analysis: Mold design defects, insufficient mold machining accuracy, insufficient mold base accuracy and inadequate size control.

Project:

1. In the mold design, the key dimensions should be clearly marked and the tolerances should be reasonable. Each process should be strictly measured and controlled in place for key dimensions and assembly dimensions, from parts processing to assembly;

2. The precision of the mold base should also ensure the accuracy of frame opening and positioning;

3. Based on the material theoretical shrinkage rate and product structure characteristics, grab a reasonable material shrinkage rate.

The influence of size will directly lead to the product accuracy during hot-pressing riveting assembly and the use effect of the finished product after riveting. Therefore, the requirements of the tolerance range for the machine must be considered when making one-time tissue-clamping riveting tooling.

2. Product burrs

Analysis: The burrs are mainly produced in the fittings and parting surfaces of the inserts.

1. The mold design needs to be reasonable and rigorous, and the corresponding characteristics of the material should be comprehensively evaluated;

2. Define the dimensional tolerance assembly requirements of each workpiece;

3. Guarantee the accuracy of each part of mold processing;

4. Professional mold assembly method.

3. Into the point residue

Analysis: The design of the entry point structure is unreasonable, and the ejection is unbalanced.

1. The entry point structure should be designed reasonably and effectively;

2. The layout of the product ejector pins needs to be reasonable to ensure the ejection balance.

4. Insufficient strength at the crescent of the adjustment hole

Analysis: The structural strength design at the crescent of the product is insufficient, the final position of the bonding line is unreasonable, and the molding process setting is unreasonable.

1. The structural strength of the product crescent should be reasonably designed;

2. The layout of the entry point should be reasonable;

3. Set reasonable process parameters;

4. The corresponding exhaust at the joint line should be unobstructed.

5. The closing effect is not good

Analysis:

1. The design of the inter-occlusal feature of the tissue clip itself;

2. Product-related structural features are not strong enough;

3. The precision of mold processing related features is not enough;

4. The molding process setting is unreasonable.

1. Product-related occlusal features should be designed reasonably and effectively;

2. The strength of the relevant parts of the product should be designed reasonably;

3. Ensure mold machining accuracy;

4. Set a reasonable molding process.

Contact Info


Address: No. 1668 Huacheng Road, Jintan District, Changzhou city, Jiangsu Province

Phone: 86-519-82982668

Mobile: 86-18118332098

E-mail: 503472568@qq.com

Wechat


微信二维码

Website


手机官网

Copyright© 2022 Jiangsu Longtaifeng Medical Equipment Co., Ltd.  Powered by www.300.cn

This site supports IPV6  SEO

  • Hotline

    Hotline

    519-82982668

  • Mobile

    Mobile

    86-18118332098

  • E-mail

    E-mail

    503472568@qq.com

  • Follow

    Follow